Lot #57: Used Crestron AMP2210T 2 Channel Slim Power Amplifier

Used Crestron AMP2210T 2 Channel Slim Power Amplifier Tested And In Good Working Condition Includes Phoenix Style Input, Output & Remote Connectors Overview: Crestron AMP-series Commercial Power Amplifiers provide a perfect combination of high output and efficiency for all types of professional audio applications. 100% Crestron engineered and built, these amplifiers are designed for energy efficiency to enable organizations to fulfill their green initiatives without compromising on audio performance. Advanced design features include a high-efficiency amp topology with active power factor corrected power supply, delivering a generous amount of power in a space-saving 1U rack-mountable chassis. Specifications: Audio Typical of 2 mono amplifier channels: -Input Signal Type Balanced or unbalanced analog line-level -Output Signal Types 4/8 Ohm, 70 Volt, or 100 Volt -Output Power 120 Watts at 8 Ohms; 210 Watts at 4 Ohms; 420 Watts at 8 Ohms bridged; 120 Watts at 70 or 100 Volts (Transformer isolated) -Damping Factor >100 -Protection Over Current, Over/Under Voltage, Over Temperature, DC Offset -Frequency Response 20Hz to 20kHz 0.5 dB at 4/8 Ohms; 80Hz to 20kHz +0/-3 dB at 70/100 Volts -THD: 0.05% @ 1kHz, full rated power at 4/8 Ohms, 8 Ohms Bridged, or 70/100 Volts; 0.1% @ 20Hz to 20kHz, 120W at 8 Ohms; 0.2% @ 20Hz to 20kHz, 210W at 4 Ohms; 0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged; 0.1% @ 80Hz to 20kHz, 120W at 70/100 Volts -S/N Ratio >103 dB, A-weighted -Crosstalk >70 dB @ 1kHz -Gain: 23 dB with INPUT LEVEL control set at 12 o'clock nominal position -Input Sensitivity 2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o'clock nominal position -Input Detection Threshold 40 mV RMS @ 1 kHz -Input Level Adjustment 10 dB from nominal -Connectors G 6-32 screw, chassis ground lug INPUT CH 1 – 2 (2) 3-pin 3.5mm detachable terminal blocks; -Balanced / unbalanced line-level audio inputs; -Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position; -Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced -SPEAKER OUTPUT CH 1 – 2: (2) 4-pin 7.62mm 15A detachable terminal blocks; -4Ω/8Ω and 70/100V power amplifier outputs; -Wire Size: Terminals accept up to 14 AWG REMOTE (1) 6-pin 3.5mm detachable terminal block; Provides (2) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures; -inputs may be safely paralleled for global control -FUSE T6.3AH 250V Main fuse holder; 5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated -100-240V50/60Hz (1) IEC C14 male chassis plugs, main power input; -Mates with removable power cord (included) -Controls & Indicators: -PWR (1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state -INPUT 1 – 2, SIGNAL (2) green LEDs, indicate signal presence on each corresponding channel -OUTPUT 1 – 2, CLIP (2) amber LEDs, indicate a clipping condition on each corresponding channel -OUTPUT 1 – 2, FAULT (2) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel -INPUT CH 1 – 2 LEVEL (rear) (2) Rotary input boost/attenuate adjustments w/center detent at nominal -SPEAKER OUTPUT CH 1 – 2, 100V / 70V / 4/8Ω (rear) (2) 3-position slide switches, select the output configuration for each corresponding channel -ON/REMOTE/OFF (rear) (1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel -Power Requirements Main Power 100-240 Volts AC, 50/60 Hz Power Consumption: 62 Watts @ 8 Ohms, all channels driven at 1/8th output power; 88 Watts @ 4 Ohms, all channels driven at 1/8th output power; 63 Watts @ 70/100V, all channels driven at 1/8th output power; 26 Watts, all channels idle; Pickup category timeslot {C}